Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't take too lightly the forklift at work. If the operation is not good, there will be serious crashes in minutes, and there are many mishaps including forklifts.

Situation 1: The forklift cargo blocked the chauffeur's view, and the individual ahead might not be located, resulting in a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty products, the staff members utilized their body weight as the counterweight, which virtually created casualties.
Situation 3: The width of the forklift freight exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an crash.
Case 4: Forklift is speeding up and surrender throughout a turn.
Instance 5: The forklift vehicle driver did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the workers unlawfully, the forklift motorist does not use the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift vehicle driver did not use a safety belt and fell from the automobile when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before starting, observe the surroundings, and after verifying that there are no barriers that impede the safety and security of driving, beep the horn initially and afterwards begin.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale need to be secure prior to beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is stable and trustworthy.
4. The begin must be sluggish and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be slanted backwards. .
2. Do not raise the fork too expensive when driving. When entering and leaving the job website or while driving, take care that there will be no barriers in the sky. When the tons is traveling, the fork must not be increased too high, which will certainly influence the stability of the forklift. .
3. After dumping, the fork ought to be lowered to the regular driving setting before driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal ought to be released first. High-speed sharp turns are banned. High-speed sharp turns will trigger the vehicle to lose lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be appropriately tilted back. The tons shall not be raised except when stacking or loading. .
8. The elevation of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product affects the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The tons needs to be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to utilize forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to choose, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be examined, and fuel, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak needs to likewise Electric Forklift Truck for Warehouse be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you encounter a person before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is Electric Forklift Truck for Warehouse allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844